MC542G Two-phase 57 Series Stepper Driver

Product Overview

The MC542G is a 57 digital stepper driver developed based on a high-performance, low-power ARM chip. Its driver features a built-in intelligent regulator with PID parameter self-tuning functionality, which automatically generates the most suitable parameters for different motors without manual adjustment, optimizing motor performance. This driver operates the motor with very low noise.

Features

Voltage input range: DC 20V to 50V Maximum peak current: 4.2A Subdivision range: 400 to 25600 ppr Pulse form: Pulse + direction, AB phase Pulse response frequency: 0 to 200KHz Automatic motor parameter tuning function Features protection functions such as overvoltage, overcurrent, and tracking error exceeding limits

Product Overview Supporting Products Data Download

Driver Function Description

Driver Functions	Operating Instructions
Operating Current Setting	Set by SW1-SW3 three DIP switches to set the driver output current, with a total of 8 levels. For specific output current settings, please refer to the driver panel instructions.
Automatic Half-Current Function	Users can set the driver's automatic half-current function through SW4 . OFF means the static current is set to half of the dynamic current, ON means the static current is the same as the dynamic current. Generally, it is recommended to set SW4 to OFF to reduce the heat generated by the motor and driver and improve reliability. After the pulse train stops, the current automatically reduces after about 0.3 seconds. 50% (Actual value 55% ), theoretically reducing heat generation by 65%。
Microstep Subdivision Setting	Set by SW5-SW8 Four DIP switches are used to set the driver's microstep subdivision, with a total of 15 microstep levels. When setting the subdivision, the driver should be stopped first. For specific microstep subdivision settings, please refer to the driver panel instructions.
Indicator Lights	The driver has two indicator lights: red and green. The green light is the power indicator and stays on when the driver is powered; the red light is the fault indicator and stays on when overvoltage or overcurrent faults occur. The red light turns off after the fault is cleared. When a fault occurs, only power cycling and re-enabling can clear the fault.
Signal Interface	PUL+ and PUL- are the positive and negative terminals of the control pulse signal; DIR+ and DIR- are the positive and negative terminals of the direction signal; ENA+ and ENA- are the positive and negative terminals of the enable signal.
Motor Interface	A+ and A- connects to the positive and negative terminals of the A-phase winding of the stepper motor; A phase winding; B+ and B- connects to the positive and negative terminals of the A-phase winding of the stepper motor; B phase winding. Swapping the two-phase windings can reverse the motor direction. A 、 B When the two-phase windings are swapped, the motor direction reverses.
Power Interface	Powered by DC power supply, operating input voltage range: 20~50VDC , recommended operating voltage 36VDC ', power supply capacity greater than' 100W.
Installation Instructions	Driver dimensions are: 117 × 78 × 34mm with mounting hole spacing of 111mm . It can be installed horizontally or vertically (vertical installation is recommended). During installation, it should be mounted tightly against a metal cabinet to facilitate heat dissipation.

Product Diagram

Parameter Settings

The MC542G driver uses an eight-position DIP switch to set subdivision accuracy, dynamic current, and half/full current, described in detail as follows:

Operating Current Setting

Output Peak Current	Output Average Current	SW1	SW2	SW3
1.00A	0.71A	on	on	on
1.46A	1.04A	off	on	on
1.91A	1.36A	on	off	on
2.37A	1.69A	off	off	on
2.84A	2.03A	on	on	off
3.31A	2.36A	off	on	off
3.76A	2.69A	on	off	off
4.20A	3.00A	off	off	off

Microstep Subdivision Setting

Steps / Revolutions	SW5	SW6	SW7	SW8
Default	on	on	on	on
400	off	on	on	on
800	on	off	on	on
1600	off	off	on	on
3200	on	on	off	on
6400	off	on	off	on
12800	on	off	off	on
25600	off	off	off	on
1000	on	on	on	off
2000	off	on	on	off
4000	on	off	on	off
5000	off	off	on	off
8000	on	on	off	off
10000	off	on	off	off
20000	on	off	off	off

Main Application Areas

Suitable for various motion control automation equipment and instruments, such as electronic processing and inspection, semiconductor packaging, laser cutting and welding, laser typesetting, packaging machinery, engraving machines, marking machines, cutting machines, garment plotters, CNC machine tools, and automated assembly equipment.

Two-phase 57 Series (1.8°) Hybrid Stepper Motor

< 1 > proceed page